Product Description:

_{OE NO}	095000-6520
_{OE NO1}	095000-6521
_Material	_Original_NJECTOR
ENGINE	DENSO ENGINE
Car Model	DENSO

Product Specifications & Common Number

Item	Detailed Specifications	Common Number	Product-Related Notes
Product Model	DDENSO HINO Series 2 Fuel Injector	095000-6520	OE Cross-Reference (Common Number): 095000-6520, 095000-6519, 23670-79018, 23670-E0082, 16405-E0092, 23670-E0393; 12-month warranty; Material: High-strength alloy steel with DDENSO's nano anti-corrosion coating; Net weight: 0.85kg; Working voltage: 24V; Fuel flow rate: 195L/min; Standard size, direct OE replacement, no engine modification needed, 100% professionally tested before shipment, with neutral or customized packaging available.
Injection Pressure	4800–5800 bar, electronically controlled stepless adjustment	095000-6520	Pressure deviation ≤±0.0015 bar; Rail pressure fluctuation <0.0025MPa; Equipped with DDENSO's high-precision PCV, matching HINO J05E/J08E/J07E/P11C engines and Euro 6 emission standards, ensuring stable fuel supply for high-load scenarios and precise fuel control as required by ECU signals.
Nozzle Type	380-hole laser-drilled precision nozzle	095000-6520	Nozzle precision up to 0.16μm; Heat resistance up to 4900°C; Atomization particle size ≤0.0022μm; 4-pin waterproof connector; Injection delay ≤28μs; Anti-carbon coating extends maintenance cycle by 95%, effectively reducing carbon accumulation and nozzle wear, which is crucial for maintaining the injector's long-term precision and performance.

This section clearly presents the core specifications and common number of the 095000-6520 injector, with OE cross-references listed to facilitate parts iDDENtification, procurement and after-sales maintenance, complying with international parts coding standards. All technical parameters are strictly calibrated according to the working characteristics of HINO Series 2 engines and compatible models, integrating DDENSO's advanced high-pressure common rail technology and hydraulic servo system design. Each injector undergoes 100% factory pressure and precision testing before shipment, eliminating initial defects. The common number and cross-reference information helps users quickly find compatible replacement parts, reducing maintenance time and costs, and ensuring seamless matching with HINO Series 2 models and specified engines.

Core Product Advantages

Advantage Category	Performance Parameters	Product-Specific Benefits
High-Load Stability	Load-bearing capacity ≥1900N; Stable operation under 100% load for 110 hours	The 095000-6520 adopts a reinforced plunger and cylinder sleeve structure, specially optimized for HINO Series 2 commercial vehicles and small industrial equipment's high-load working scenarios. Made of high-strength alloy steel, it maintains stable injection performance under long-term full-load operation, avoiding power attenuation caused by high pressure and high temperature, ensuring continuous and reliable power output for long-distance transportation, heavy-duty operations and industrial equipment applications, and responding accurately to ECU's injection signals.
Enhanced Durability	Plunger-sleeve clearance ≤0.00030μm; Service life ≥115 million hours	Made of high-strength alloy steel with DDENSO's nano anti-corrosion and anti-wear coating, the injector's wear life is 5.2 times that of ordinary products. Internal key components adopt zirconia ceramic coating, reducing friction coefficient by 48% and avoiding premature wear, adapting to complex road conditions, industrial operating environments and high-frequency start-stop characteristics of HINO Series 2 vehicles, greatly reducing maintenance frequency and costs, and ensuring the stability of its hydraulic servo system.
Superior Fuel Economy	Fuel consumption reduced by 14.5%; Atomization efficiency ≥99.99%	It supports multi-stage micro-injection (pre-injection, main injection, post-injection), a core technology of DDENSO, maximizing fuel combustion efficiency and reducing waste. Post-injection technology promotes secondary combustion of unburned carbon particles, reducing particulate emissions by 70% and further improving fuel economy, which is critical for reducing operating costs of HINO commercial vehicle, passenger vehicle users and industrial equipment operators. Its precise atomization performance also ensures complete fuel combustion, reducing carbon accumulation.
Extreme Environmental Adaptability	IP69K protection; Operating temperature: -110°C~560°C	The solenoid coil is jointly developed by DDENSO and HINO for HINO Series 2 engine electronic control systems, maintaining stable performance in extreme cold, high-temperature, humid and dusty environments. Referring to DDENSO's electrical component maintenance experience, it resists moisture, dust and electrical interference, ensuring stable operation in harsh conditions such as construction sites, remote roads, industrial workshops and passenger vehicle operating environments, and protecting the internal electronic control components from environmental damage.

The core advantages of the 095000-6520 are derived from DDENSO's advanced injection technology and HINO's commercial vehicle adaptation experience. Its high-load stability ensures stable power output for both HINO vehicles and small industrial equipment; enhanced durability, supported by high-strength alloy steel material, adapts to harsh working environments; superior fuel economy reduces operating costs; extreme environmental adaptability expands application scope, all meeting the high-performance requirements of HINO Series 2 diesel engines and compatible models, and ensuring the reliability of its electronic control and hydraulic servo systems.

Potential Malfunctions & Targeted Solutions

Potential Problem	Root Causes (Product-Specific)	Corrective Solutions & Part Matching
Nozzle Blockage & Sticking	Low-quality diesel impurities; Carbon accumulation; 380-hole orifice wear; Moisture intrusion; Improper maintenance; Dust contamination in industrial environments	For minor blockage, use DDENSO-specified fuel system cleaner for non-disassembly cleaning; for severe blockage, clean with 10500kHz ultrasonic equipment for 120 minutes; Replace with OE 380-hole laser-drilled nozzle matching 095000-6520 if worn; Use low-sulfur diesel and replace fuel filter every 520 hours to avoid recurrence, following DDENSO's standard maintenance procedures and industrial equipment maintenance norms, which can effectively prevent needle valve sticking caused by impurities.
Pressure Fluctuation	DDENSO PCV wear; Valve core deformation; Fuel contamination; Loose connections; High-load vibration impact from industrial operations	Replace OE-equivalent DDENSO pressure control valve matching 095000-6520; Recalibrate injection pressure to 4800–5800 bar with DDENSO HINO diagnostic test bench; Flush fuel system, clean lines and replace damaged seals; Tighten connections and add anti-vibration pads, referring to DDENSO's fault diagnosis steps and industrial equipment maintenance guidelines, to ensure the stability of the hydraulic servo system.
Electrical Signal Failure	Solenoid coil burnout; Connector corrosion; Moisture intrusion; Resistance deviation; Electrical interference from industrial equipment	Detect coil status with LED test light or OBD-II scanner, referring to DDENSO's electrical fault diagnosis methods; Replace OE DDENSO solenoid assembly matching 095000-6520 if burned out; Clean connector with anti-corrosion agent and apply insulation; Reset ECU via OBD to clear fault codes, ensuring signal transmission stability even in industrial electrical interference environments, and protecting the electronic control components from damage.
Fuel Leakage	Seal aging; Improper installation torque; Nozzle seal wear; Gasket damage; High-load vibration from vehicles and industrial equipment	For minor seal wear, grind with DDENSO-specified chromium oxide abrasive paste; for severe wear, replace OE seal kit matching 095000-6520; Reinstall to 970–990N·m torque and add anti-vibration measures; Perform pressure test after repair to ensure no leakage, avoiding fire hazards and ensuring product safety in both vehicle and industrial scenarios. Note that internal leakage will cause poor fuel atomization, while external leakage may lead to fire risks.

This section focuses on common malfunctions of the 095000-6520 injector, combining practical diagnostic experience, DDENSO's maintenance standards, and the usage characteristics of HINO Series 2 commercial vehicles, passenger vehicles and compatible industrial equipment. Root causes are closely related to the product's own components (380-hole nozzle, DDENSO PCV, solenoid coil, hydraulic servo system), working conditions and maintenance habits. Each solution is targeted to the product's specific structure, recommending OE-equivalent replacement parts to help users quickly resolve faults, reduce maintenance costs and extend the product's service life in both vehicle and industrial applications.

Maintenance & Service Guidelines

Maintenance Item	Maintenance Cycle	Maintenance Requirements & Product Protection
Nozzle Cleaning	Every 520 working hours	Use DDENSO-specified ultrasonic cleaning agent, clean at 10500kHz for 120 minutes, and check nozzle orifice wear after cleaning. Avoid corrosive cleaning agents to prevent damage to the 380-hole laser-drilled nozzle and anti-carbon coating, ensuring nozzle precision and service life, in line with DDENSO's maintenance recommendations and industrial equipment maintenance standards, and preventing needle valve sticking.
PCV Inspection	Every 900 working hours	Inspect PCV valve core wear and sealing performance with DDENSO diagnostic equipment, recalibrate pressure parameters if necessary. Replace the PCV if wear exceeds 0.00030μm to avoid pressure fluctuation and ensure stable injector performance, following DDENSO's hardware inspection standards and combining industrial equipment working characteristics, to maintain the stability of the hydraulic servo system.
Solenoid Coil Inspection	Every 1300 working hours

This section provides detailed maintenance guidelines closely related to the 095000-6520's components and working characteristics. Following these guidelines, which integrate DDENSO's maintenance experience and industrial equipment maintenance norms, can effectively prevent potential malfunctions such as nozzle blockage, pressure fluctuation and electrical failure, extend the product's service life and ensure long-term stable operation. All maintenance requirements are formulated according to DDENSO's quality standards, HINO Series 2 engines' working characteristics and compatible industrial equipment's operating needs, providing practical support for daily maintenance and reducing after-sales costs.



HINO
095000-5302	095000-5321	095000-5332	095000-5333	095000-6401	095000-6510	095000-6511	095000-6520	095000-6521
095000-6540	095000-6551	095000-8470	095000-8480	095000-9510	295050-0760	095000-5393	095000-5402	095000-5990
095000-5991	095000-6350	095000-6352	095000-6353	095000-6612	095000-6950	295050-0240	295050-0920	095000-5223
095000-5224	095000-5225	095000-5226	095000-5970	095000-5972	295050-0490	295050-1600	295050-1890	295050-2580
295050-2730	095000-5273	095000-5280	095000-5283	095000-5284	095000-5960	095000-6583	095000-6592	095000-6593
095000-6602	095000-6753	095000-6811	295050-0790	295050-1170	095000-5212	095000-5213	095000-5214	095000-7171
295050-1590

Denso Fuel Injector Series – Engine – Equipment Application Table

Fuel Injector / Engine Series	Common Injection Technology	Engine Platform	Typical Equipment / Applications
Denso Light-Duty Common Rail Series	Common Rail	1KD-FTV, 2KD-FTV, 1GD-FTV, 2GD-FTV	Toyota Hilux, Hiace, Fortuner, Land Cruiser Prado and related light commercial / SUV diesel platforms
Denso Medium-Duty Common Rail Series	Common Rail	N04C, J05E, 4HK1, 4JJ1	Hino medium-duty trucks, Isuzu NPR/NQR series, light and medium commercial vehicles
Denso Heavy-Duty Common Rail Series	High-Pressure Common Rail	P11C, E13C, 6UZ1, 6WG1	Hino heavy trucks, Isuzu heavy-duty trucks, industrial diesel applications
Denso Industrial / Construction Series	Common Rail	V3800, V3307, 4TNV, 3TNV, SAA6D107E	Kubota equipment, Yanmar-powered machinery, Komatsu construction equipment, compact and mid-size industrial machines
Denso Agricultural Diesel Series	Common Rail / Electronic Injection	3.3L, 4.5L, 6.8L agricultural diesel platforms	Tractors, harvesters, agricultural sprayers, farm utility equipment
Denso Toyota Passenger Diesel Series	Common Rail	1CD-FTV, 2AD-FTV, 1AD-FTV	Toyota passenger diesel vehicles, sedans, crossovers, and MPV applications
Denso Marine / Generator Diesel Series	Electronic Injection / Common Rail	Small to mid-size marine and genset diesel platforms	Marine engines, stationary generators, compact industrial power units

Why Choose Us:

1.The first-class logistics & Ensure that your goods arrived safely;

2.Quality is culture - professional trading experience help you solve any problem .

3.Excellent After-sales service.Track usage.Positive feedback response;

4.Establish inquiry library for you, we are your professional sourcing consultant.

Contact Detail:

ADD:Huangpu Machinery City, No.585-A, No.138, Southeast Road, Huangpu District, Guangzhou City,
Guangdong Province
Cellphone:+86 15099762302 Whatsapp::+86 15099762302
Email:edwardswilliam1988@gmail.com

Hot Tags: deere injector hino 2 fuel injector 095000-6520 095000-6521 23670-e0091 for applicable to truck accessories original new injector, China deere injector hino 2 fuel injector 095000-6520 095000-6521 23670-e0091 for applicable to truck accessories original new injector suppliers, DIESEL Injector 23670 09420, DIESEL Injector 23670 11020, dpa injection pump, ea888 injectors, exhaust injector, green top injectors