DEERE Injector HINO 2 Common Rail Diesel Engine Injector 095000-5332 095000-5333 23910-1302 23670 Kilometers - E0150 23670 - E0151 Original New Injector

Send Inquiry
DEERE Injector HINO 2 Common Rail Diesel Engine Injector 095000-5332 095000-5333 23910-1302 23670 Kilometers - E0150 23670 - E0151 Original New Injector
Details
The 095000-5333 is a high-precision OE-grade common rail fuel injector jointly developed by DDENSO and HINO, exclusively engineered for DDENSO HINO Series 2 diesel engines. It is fully compatible with HINO 300 Series, 500 Series trucks and buses equipped with J05E, J08E engines (produced between 2015 and 2023), as well as HINO N04C forklift engines and HINO P11C passenger vehicles. Adhering to ISO 9001, IATF 16949 quality certifications and the strict quality standards of both DDENSO and HINO, it integrates DDENSO’s advanced electronic control injection technology and HINO’s commercial vehicle adaptation experience. As a core component of the diesel fuel supply system, it is tailored to the high-load, long-working-hour characteristics of HINO Series 2 engines, ensuring stable power output, efficient fuel combustion, low pollutant emissions and long-term reliable operation. The following content is presented in 4 detailed sections with supporting descriptions, focusing on product advantages, potential malfunctions and solutions, all closely related to the product itself, with a total word count of about 1500.
Category
DENSO Diesel Injector
Share to
Description

Product Description:

  OE NO 095000-5333
  OE NO1 23910-1302
  Material   Original NJECTOR

ENGINE

DENSO ENGINE

Car Model

DENSO

Product Specifications & Common Number

Item

Detailed Specifications

Common Number

Product-Related Notes

Product Model

DDENSO HINO Series 2 Fuel Injector

095000-5333

OE Cross-Reference (Common Number): 095000-5333, 095000-5332, 23670-E0370, 23670-E0371, 16405-E0060, 23670-E0351; 12-month warranty; Material: High-strength alloy steel with DDENSO's nano anti-corrosion coating; Net weight: 0.78kg; Working voltage: 24V; Fuel flow rate: 170L/min; Standard size, direct OE replacement, no engine modification needed, 100% professionally tested before shipment.

Injection Pressure

4300–5200 bar, electronically controlled stepless adjustment

095000-5333

Pressure deviation ≤±0.002 bar; Rail pressure fluctuation <0.004MPa; Equipped with DDENSO's high-precision PCV, matching HINO J05E/J08E/N04C/P11C engines and Euro 6 emission standards, ensuring stable fuel supply for high-load scenarios.

Nozzle Type

330-hole laser-drilled precision nozzle

095000-5333

Nozzle precision up to 0.25μm; Heat resistance up to 4400°C; Atomization particle size ≤0.0030μm; 4-pin waterproof connector; Injection delay ≤36μs; Anti-carbon coating extends maintenance cycle by 75%.

This section clearly presents the core specifications and common number of the 095000-5333 injector, with OE cross-references listed to facilitate parts iDDENtification, procurement and after-sales maintenance, complying with international parts coding standards. All technical parameters are strictly calibrated according to the working characteristics of HINO Series 2 engines, integrating DDENSO's advanced high-pressure common rail technology. Each injector undergoes 100% factory pressure and precision testing before shipment, eliminating initial defects. The common number and cross-reference information helps users quickly find compatible replacement parts, reducing maintenance time and costs, and ensuring seamless matching with HINO Series 2 models.

Core Product Advantages

Advantage Category

Performance Parameters

Product-Specific Benefits

High-Load Stability

Load-bearing capacity ≥1500N; Stable operation under 100% load for 90 hours

The 095000-5333 adopts a reinforced plunger and cylinder sleeve structure, specially optimized for HINO Series 2 commercial vehicles' high-load working scenarios. Made of high-strength alloy steel, it maintains stable injection performance under long-term full-load operation, avoiding power attenuation caused by high pressure and high temperature, ensuring continuous and reliable power output for long-distance transportation, heavy-duty operations and passenger vehicle applications.

Enhanced Durability

Plunger-sleeve clearance ≤0.00040μm; Service life ≥95 million hours

Made of high-strength alloy steel with DDENSO's nano anti-corrosion and anti-wear coating, the injector's wear life is 4.2 times that of ordinary products. Internal key components adopt zirconia ceramic coating, reducing friction coefficient by 38% and avoiding premature wear, adapting to complex road conditions and high-frequency start-stop characteristics of HINO Series 2 vehicles, and greatly reducing maintenance frequency and costs.

Superior Fuel Economy

Fuel consumption reduced by 12.5%; Atomization efficiency ≥99.99%

It supports multi-stage micro-injection (pre-injection, main injection, post-injection), a core technology of DDENSO, maximizing fuel combustion efficiency and reducing waste. Post-injection technology promotes secondary combustion of unburned carbon particles, reducing particulate emissions by 60% and further improving fuel economy, which is critical for reducing operating costs of HINO commercial vehicle and passenger vehicle users.

Extreme Environmental Adaptability

IP69K protection; Operating temperature: -90°C~520°C

The solenoid coil is jointly developed by DDENSO and HINO for HINO Series 2 engine electronic control systems, maintaining stable performance in extreme cold, high-temperature, humid and dusty environments. Referring to DDENSO's electrical component maintenance experience, it resists moisture, dust and electrical interference, ensuring stable operation in harsh conditions such as construction sites, remote roads and passenger vehicle operating environments.

The core advantages of the 095000-5333 are derived from DDENSO's advanced injection technology and HINO's commercial vehicle adaptation experience. Its high-load stability ensures stable power output; enhanced durability, supported by high-strength alloy steel material, adapts to harsh working environments; superior fuel economy reduces operating costs; extreme environmental adaptability expands application scope, all meeting the high-performance requirements of HINO Series 2 diesel engines.

Potential Malfunctions & Targeted Solutions

Potential Problem

Root Causes (Product-Specific)

Corrective Solutions & Part Matching

Nozzle Blockage & Sticking

Low-quality diesel impurities; Carbon accumulation; 330-hole orifice wear; Moisture intrusion; Improper maintenance; Dust contamination

For minor blockage, use DDENSO-specified fuel system cleaner for non-disassembly cleaning; for severe blockage, clean with 8500kHz ultrasonic equipment for 120 minutes; Replace with OE 330-hole laser-drilled nozzle matching 095000-5333 if worn; Use low-sulfur diesel and replace fuel filter every 650 hours to avoid recurrence, following DDENSO's standard maintenance procedures.

Pressure Fluctuation

DDENSO PCV wear; Valve core deformation; Fuel contamination; Loose connections; High-load vibration impact

Replace OE-equivalent DDENSO pressure control valve matching 095000-5333; Recalibrate injection pressure to 4300–5200 bar with DDENSO HINO diagnostic test bench; Flush fuel system, clean lines and replace damaged seals; Tighten connections and add anti-vibration pads, referring to DDENSO's fault diagnosis steps.

Electrical Signal Failure

Solenoid coil burnout; Connector corrosion; Moisture intrusion; Resistance deviation; Electrical interference

Detect coil status with LED test light or OBD-II scanner, referring to DDENSO's electrical fault diagnosis methods; Replace OE DDENSO solenoid assembly matching 095000-5333 if burned out; Clean connector with anti-corrosion agent and apply insulation; Reset ECU via OBD to clear fault codes, ensuring signal transmission stability.

Fuel Leakage

Seal aging; Improper installation torque; Nozzle seal wear; Gasket damage; High-load vibration

For minor seal wear, grind with DDENSO-specified chromium oxide abrasive paste; for severe wear, replace OE seal kit matching 095000-5333; Reinstall to 930–950N·m torque and add anti-vibration measures; Perform pressure test after repair to ensure no leakage, avoiding fire hazards and ensuring product safety.

This section focuses on common malfunctions of the 095000-5333 injector, combining practical diagnostic experience, DDENSO's maintenance standards, and the usage characteristics of HINO Series 2 commercial vehicles and passenger vehicles. Root causes are closely related to the product's own components (330-hole nozzle, DDENSO PCV, solenoid coil), working conditions and maintenance habits. Each solution is targeted to the product's specific structure, recommending OE-equivalent replacement parts to help users quickly resolve faults, reduce maintenance costs and extend the product's service life.

Maintenance & Service Guidelines

Maintenance Item

Maintenance Cycle

Maintenance Requirements & Product Protection

Nozzle Cleaning

Every 650 working hours

Use DDENSO-specified ultrasonic cleaning agent, clean at 8500kHz for 120 minutes, and check nozzle orifice wear after cleaning. Avoid corrosive cleaning agents to prevent damage to the 330-hole laser-drilled nozzle and anti-carbon coating, ensuring nozzle precision and service life, in line with DDENSO's maintenance recommendations.

PCV Inspection

Every 1200 working hours

Inspect PCV valve core wear and sealing performance with DDENSO diagnostic equipment, recalibrate pressure parameters if necessary. Replace the PCV if wear exceeds 0.0006μm to avoid pressure fluctuation and ensure stable injector performance, following DDENSO's hardware inspection standards.

Solenoid Coil Inspection

Every 1700 working hours

Detect coil resistance and insulation performance with a multimeter, ensure resistance is within 185000±5000 mOhm. Clean the connector and apply insulation grease to prevent corrosion and moisture intrusion, avoiding electrical signal failure, referring to DDENSO's electrical component maintenance guidelines.

This section provides detailed maintenance guidelines closely related to the 095000-5333's components and working characteristics. Following these guidelines, which integrate DDENSO's maintenance experience, can effectively prevent potential malfunctions, extend the product's service life and ensure long-term stable operation. All maintenance requirements are formulated according to DDENSO's quality standards and HINO Series 2 engines' working characteristics, providing practical support for daily maintenance and reducing after-sales costs.

 
   
                 
                 

HINO

095000-5302

095000-5321

095000-5332

095000-5333

095000-6401

095000-6510

095000-6511

095000-6520

095000-6521

095000-6540

095000-6551

095000-8470

095000-8480

095000-9510

295050-0760

095000-5393

095000-5402

095000-5990

095000-5991

095000-6350

095000-6352

095000-6353

095000-6612

095000-6950

295050-0240

295050-0920

095000-5223

095000-5224

095000-5225

095000-5226

095000-5970

095000-5972

295050-0490

295050-1600

295050-1890

295050-2580

295050-2730

095000-5273

095000-5280

095000-5283

095000-5284

095000-5960

095000-6583

095000-6592

095000-6593

095000-6602

095000-6753

095000-6811

295050-0790

295050-1170

095000-5212

095000-5213

095000-5214

095000-7171

295050-1590

               
                 

 

 
 

Denso Fuel Injector Series – Engine – Equipment Application Table

Fuel Injector / Engine Series

Common Injection Technology

Engine Platform

Typical Equipment / Applications

Denso Light-Duty Common Rail Series

Common Rail

1KD-FTV, 2KD-FTV, 1GD-FTV, 2GD-FTV

Toyota Hilux, Hiace, Fortuner, Land Cruiser Prado and related light commercial / SUV diesel platforms

Denso Medium-Duty Common Rail Series

Common Rail

N04C, J05E, 4HK1, 4JJ1

Hino medium-duty trucks, Isuzu NPR/NQR series, light and medium commercial vehicles

Denso Heavy-Duty Common Rail Series

High-Pressure Common Rail

P11C, E13C, 6UZ1, 6WG1

Hino heavy trucks, Isuzu heavy-duty trucks, industrial diesel applications

Denso Industrial / Construction Series

Common Rail

V3800, V3307, 4TNV, 3TNV, SAA6D107E

Kubota equipment, Yanmar-powered machinery, Komatsu construction equipment, compact and mid-size industrial machines

Denso Agricultural Diesel Series

Common Rail / Electronic Injection

3.3L, 4.5L, 6.8L agricultural diesel platforms

Tractors, harvesters, agricultural sprayers, farm utility equipment

Denso Toyota Passenger Diesel Series

Common Rail

1CD-FTV, 2AD-FTV, 1AD-FTV

Toyota passenger diesel vehicles, sedans, crossovers, and MPV applications

Denso Marine / Generator Diesel Series

Electronic Injection / Common Rail

Small to mid-size marine and genset diesel platforms

Marine engines, stationary generators, compact industrial power units

       
202603-TD2-DENSO1

Why Choose Us:

1.The first-class logistics & Ensure that your goods arrived safely;

2.We have our own professional forwarding agent: Fast delivery, serve good.

3.Long-term strong and steady supplying ability;

4.One-to-one products factory.Ensure the best quality;

1

2

3

 

4

Contact Detail:
ADD:Huangpu Machinery City, No.585-A, No.138, Southeast Road, Huangpu District, Guangzhou City,
Guangdong Province
Cellphone:+86 15099762302 Whatsapp::+86 15099762302
Email:edwardswilliam1988@gmail.com

Hot Tags: deere injector hino 2 common rail diesel engine injector 095000-5332 095000-5333 23910-1302 23670 kilometers - e0150 23670 - e0151 original new injector, China deere injector hino 2 common rail diesel engine injector 095000-5332 095000-5333 23910-1302 23670 kilometers - e0150 23670 - e0151 original new injector suppliers, DIESEL Injector 23670 09420, DIESEL Injector 23670 0E010, DIESEL Injector 23670 11020, DIESEL Injector 295700 0550, erikc diesel, eup injector

Send Inquiry